MEASURE AND CERTIFY CAT5, CAT5e, CAT6 CABLES WITH OUR CABLE TESTERS
- Detects opens, shorts, miswires and split pairs on the twisted pair cabling. - Measures length. - Low battery detector. - Auto backlit. - Auto power off.
- LCD display. - Test pin configuration for 10/100 base-T cable, 10 base-2 cable, RJ45/RJ11 modular cables, AT and T 258 A cable, EIA/TIA 568A/568B cables and Token Ring Cables etc. - Verify cable continuity, opens, shorts and miss-wired. - Auto and manual scan function. - Ground wire test. - Locked status wire function. - Detected defective wire warning (buzzer). - Function Keys: ON/OFF, Test, Auto, Lock, Manual. - Low battery indication.
Tests : UTP. FTP. Coax cables, two, three, or four wire pairs in twisted pair cables and test all category UTP cables and hardware. Verify end-to-end connectivity per EIA/TIA 568 wiring standard. Detects wiring problems : Opens, Shorts, miswires (Crossed, Reversed, Split pair). Locates wiring/connection errors (distance to the open or shout) Measures cable length
Cable Expert (Model No.: CE-1000) NanoTronix Cable Expert (Model No.: CE-1000) is the all-in-one and easy-to-use network qualification unit measuring logical network performance and physical condition of network cables. It allows network engineers to install and maintain efficiently local area networks (LAN) with 10BASE-T and 100BASE-TX based on the Ethernet protocol. For measuring logical network performance, it provides the round-trip time (RTT) testing to measure network speed under dynamic and static configuration protocol and the IP scanning to show the information on all the terminals connected into the local network. It can also evaluate the capability of link partners such as supported network speed (10BASE-T or 100BASE-TX) and duplexity (half- or full- duplex). The device provides the physical information of the LAN cable under test such as cable length, faulty positions (open or short) and wire map (open, short, split, crossed and reversed). In particular, with the novel high-resolution graphic TDR (Time-Domain Reflectometer) and TDX (Time-Domain Crosstalk), it is possible for the users to locate faulty positions along the cable up to 500 meters. These TDR and TDX can...
Identify and Find the Distance to an Open or Short in Seconds Measure Cable Length in a Box, on a Spool or in a Wall Transmit Tone Signals for Tracing Hidden Cable Runs Measure Voltage to Identify Live Circuits Extensive Built-in Library of Cable Types Compatible with All Common Cables Displays Length in Feet or Meters
The Ethernet Speed Certifier offers a complete solution to test and speed certify the data-carrying capabilities of Ethernet network cables up to 1 Gb/s by testing for noise in the network, detecting faults in the cable wiring, and ensuring that cables are able to support the speed capabilities of active equipment. Speed Certification to IEEE standards 802.3 Cable testing to TIA568A/B The advanced discovery gives the clearest vision of network layout and interfaces between active components like servers, switches, routers, etc. All the information is collected, stored, and ready for reporting. 21st century speed certification. Pings specific IPs or URL addresses DHCP Traceroute VLAN
Tests 10/100/1000 Base-T, IPV4/IPV6, VLAN, DHCP and more The model Cabling and Advanced Network Tester takes all the features and functionality of the Cable Prowler™ and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical layer and link conditions in the network. Supports IPV4 and IPV6 protocols Verifies DHCP connectivity and DNS Pings IPV4, IPV6, and URL addresses CDP, LLDP, NDP, and VLAN detection TCP/UDP Throughput Test Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps Link light to identify location on a hub/switch/router port Tests CAT3/5e/6/6a Ethernet cable configuration and verifies connectivity while conducting tests for opens, shorts, miswires, split pairs, and reverses Supports up to 8 testing and ID remotes for network & telephone cables Supports up to 20 network and coax ID-only mapping remotes Ability to define Network test name, cable name, save and print all results (cable testing and network testing)